| Author |
Message |
teo_hatz
Brekeke Member
Joined: 10 Aug 2006
Posts: 13
|
 Posted: Tue Jan 11, 2011 5:10 am Post subject: SNOM M9 problem with pbx |
 |
|
1. Brekeke Product Name and version:
PBX , SIP SERVER 2.4.7.3/286.1
2. Java version:
1.6.0_21
3. OS type and the version:
Linux
4. UA (phone), gateway or other hardware/software involved:
5. Select your network pattern from http://www.brekeke-sip.com/bbs/network/networkpatterns.html :
6. Your problem:
When a call is resumed from on hold state ,a beep sound is heard from snom m9 phone for 10 sec, which is generated from pbx as i discovered from ethereal and then recorded sound is played from m9 as the phone was recording while beep sound was heard. The user of M9 has call recording off. M9 has latest firmware. Any suggestions? Thank you. |
|
| Back to top |
|
hope
Brekeke Master Guru
Joined: 15 Jan 2008
Posts: 862
|
| Posted: Wed Jan 12, 2011 3:49 pm Post subject: |
|
|
is call recording on when call established?
| Quote: |
| recorded sound is played from m9 as the phone was recording while beep sound was heard. |
what recorded sound played, is it from brekeke pbx? |
|
| Back to top |
|
teo_hatz
Brekeke Member
Joined: 10 Aug 2006
Posts: 13
|
| Posted: Thu Jan 13, 2011 12:25 am Post subject: |
|
|
is call recording on when call established?
No
what recorded sound played, is it from brekeke pbx?
one way conversation from M9 user, while beep sound was on for 10 sec. After beep stops automaticaly i listen the m9 user what was saying 10 sec before |
|
| Back to top |
|
hope
Brekeke Master Guru
Joined: 15 Jan 2008
Posts: 862
|
| Posted: Thu Jan 13, 2011 6:46 pm Post subject: |
|
|
do you record call by using #6 or define call record on from pbx user setting?
is call disconnected after 10 seconds or call record stopped after 10 seconds, and both side can still talk?
what did you set at options/Media Server system settings/message recording length
and pbx user setting page /Message recording length (sec)? |
|
| Back to top |
|
teo_hatz
Brekeke Member
Joined: 10 Aug 2006
Posts: 13
|
| Posted: Fri Jan 14, 2011 2:33 am Post subject: |
|
|
do you record call by using #6 or define call record on from pbx user setting?
No, call record is off. i am not trying to record. I just want to resume m9 user from on hold state from m9 interface, going to option-on hold-option resume.
is call disconnected after 10 seconds or call record stopped after 10 seconds, and both side can still talk?
No, the call is not disconnected. M9 user that is the user who listen beep sound, after beep sound stops,receives sound from other user with delay. The other user can listen from m9 user normally. Then the delay is reduced to 3 sec.
what did you set at options/Media Server system settings/message recording length
and pbx user setting page /Message recording length (sec)?
600 sec , and pbx user setting page /Message recording length (sec) is empty. |
|
| Back to top |
|
hope
Brekeke Master Guru
Joined: 15 Jan 2008
Posts: 862
|
| Posted: Tue Jan 18, 2011 4:21 pm Post subject: |
|
|
| does the same issue happen if use phones other than snom m9? |
|
| Back to top |
|
teo_hatz
Brekeke Member
Joined: 10 Aug 2006
Posts: 13
|
| Posted: Wed Jan 19, 2011 2:23 am Post subject: |
|
|
does the same issue happen if use phones other than snom m9?
No, exactly. I use AAstra 6731i sip shones and works very well.
On hold function, resume, etc works fine by following aastra ready key functions.
But if i press #6 from aastra, i have similar sound beep effect generating from pbx which keeps beeping all time. I have contacted snom, but after a week no response from them. That is why I assume it has to do with recording, even if user recording is off. |
|
| Back to top |
|
|
